REDSPEC Group N Rear Brake Discs for SUBARU 290x18

REDSPEC Group N Rear Brake Discs for SUBARU 290x18

Redspec's Group N Brake Discs undergo a specific heat treatment and machining process for powerful, long-lasting braking. Used with racing brake pads, they allow drivers to brake later and help prevent temperature spikes - helping you shave time off your race results!
These discs should be mounted in place of your original brake discs (identical dimensions).
Please check carefully that the discs are compatible with your vehicle.
ISO 9001, ISO/TS 16949 and TUV approved.
Sold by pair.

Specifications :
- Rear disc
- Ventilated
- Diameter : 290 mm
- Thickness : 18 mm
- Bore : 58 mm
- Number of holes : 5

Brake discs for :
- MG EXPRESS Furgonato 160 from 03/2003 to 05/2005
- MG MG ZR 160 from 06/2001 to 04/2005
- SUBARU Impreza Station wagon (GD, GG) 2.0 WRX STi AWD from 10/2005
- SUBARU Impreza Station wagon (GD, GG) 2.5 AWD from 10/2005
- SUBARU Impreza Tre volumi (GD, GG) 2.0 AWD from 10/2005
- SUBARU Impreza Tre volumi (GD, GG) 2.0 WRX STi AWD from 02/2004
- SUBARU Impreza Tre volumi (GD, GG) 2.0 WRX STi AWD from 10/2001
- SUBARU Impreza Tre volumi (GD, GG) 2.5 AWD from 10/2005
- SUBARU Impreza Tre volumi (GD, GG) 2.5 WRX STi AWD from 09/2005

- SUBARU Legacy IV (BL, BP) 2.0, 190 Hp from 06/2005
- SUBARU Legacy IV (BL, BP) 2.0, 165 Hp from 06/2005
- SUBARU Legacy IV (BL, BP) 2.0, 179 Hp from 06/2005
- SUBARU Legacy IV (BL, BP) 2.0 R from 09/2007
- SUBARU Legacy IV (BL, BP) 3.0 R from 09/2003
- SUBARU Legacy IV Station wagon (BL, BP, B13_) 2.0 AWD, 165 Hp from 06/2005
- SUBARU Legacy IV Station wagon (BL, BP, B13_) 2.0 AWD, 179 Hp from 06/2005
- SUBARU Legacy IV Station wagon (BL, BP, B13_) 2.0 AWD, 190 Hp from 06/2005
- SUBARU Legacy IV Station wagon (BL, BP, B13_) 2.0 R AWD from 09/2007
- SUBARU Legacy IV Station wagon (BL, BP, B13_) 3.0 R AWD from 09/2003

- SUBARU Outback (BL, BP) 2.5, 173 Hp from 09/2008 to 09/2009
- SUBARU Outback (BL, BP) 2.5, 165 CV from 11/2003 to 09/2009
- SUBARU Outback (BL, BP) 3.0 AWD from 11/2003 to 09/2009

It is important to properly bed in your discs before use. Please respect the following steps:
1. Block air intake ducts approximately 3/4.
2. Use with previously bedded brake pads.
3. Use brakes lightly and intermittently for the first 15 kilometers.
4. After 15 km, you may brake normally but without any violent movements.
5. Finish by applying more pressure to the brakes: 5-6 firm, violent brakes.
6. If using heat-sensitive paint (product code CP26491), the green paint (430°C) should be white and the orange paint (560°C) should be slightly affected.

To maximise performance and longevity, your discs must be correctly balanced; in general all four discs should function at the same temperature. Discs should never exceed the working temperature range for your brake pads.